(1) Choose a film with moderate width and thickness; since aluminum profiles have complex cross-sectional shapes and significant differences between wide and narrow surfaces, edges can easily lift, reducing the film's coverage and affecting the coating quality. If the film is too narrow, it cannot provide adequate coverage, making spraying impossible. On the other hand, when selecting the film thickness, as long as it can cover the surface and has flexibility, it is sufficient; there's no need to choose an overly thick film, as it will increase the production cost of aluminum profiles and is unnecessary.
(2) Spray immediately after applying the film. After the profile is taped, spraying should be done promptly, with the shorter the waiting time, the better. If it is left for too long, the adhesive on the film can dry and lose its stickiness, especially if exposed to wind, causing the film to peel off and making spraying very difficult. Therefore, to ensure the quality of the film and coating, the waiting time after applying the film should generally not exceed 16 hours.
(3) Choose a film with moderate adhesiveness. In the production of two-color aluminum profiles, reasonable selection of the film is crucial. If the film has too low adhesiveness, it won't stick properly and may easily fall off, causing significant difficulties in spraying. If the film is too adhesive, it means there is too much glue, which can remain on the profile when the film is removed, affecting the surface quality. Additionally, when selecting a film, it is best to choose one whose adhesive composition is the same or very similar to the paint formulation, as this can reduce the impact on the color of the coating.
(4) Determine the colors, boundary surfaces, and boundary lines. Before spraying aluminum profiles, it is essential to determine which color should be applied to each surface according to the profile's function and customer requirements, identify the boundary surfaces and boundary lines, and their positions. Generally, the inner side is a lighter color and the outer side is a darker color. Only after understanding the boundary surfaces, boundary lines, and color requirements should the film be applied, ensuring that the film is positioned correctly.
(5) Film Quality: Applying the film is a key process in the processing of two-color aluminum profiles. The quality of the film directly affects the surface quality of the aluminum profiles, and mainly includes the following aspects: First, when applying the film, try not to create excessive tension in the film, meaning the film should not deform. Otherwise, the applied film is prone to shrinkage, causing the ends of the aluminum profiles to have uncoated areas. Additionally, when the film is disconnected at the ends of the aluminum profiles, it should be cut with a blade instead of being pulled apart, as pulled film will still shrink. Second, the film width should match the width of the coating surface. Generally, the film width should be slightly larger than the width of the aluminum profile surface. If the film is too wide, extending beyond the edges of the aluminum profile, it can be blown up by compressed air during spraying. If the film is too narrow and cannot fully cover the surface, it is obviously not acceptable. Fourth, when the coating boundary is at the edge of a groove, the excess film must be pressed into the groove, otherwise airflow during spraying can lift the film and affect the spray quality. Fifth, the film must be applied flat to prevent wrinkles or curling. Sixth, for profiles with complex cross-sections, if it is difficult to apply the film in one step, it can be done in two or more steps to ensure full coverage. Seventh, for aluminum profiles with thin walls or large cantilevers, the film should not be pressed too tightly, and care must be taken to avoid deformation of the profiles. Eighth, after the first spraying, the aluminum profiles should not be left standing for too long, as dust can settle on the surface, making it difficult to apply the film and thus affecting film quality.
(6) Strictly follow the film application process. Applying film to aluminum profiles must be done after the first coat of paint. Directly applying the film after chromating the profile is not allowed because the film has adhesive. If the film is applied directly to the chromated layer, the adhesive may stick to the chromated layer, or peeling off the film could strip away the chromated layer. This greatly reduces the paint film's adhesion and ultimately affects the spraying quality of the aluminum profile, leading to paint peeling, with potentially serious consequences.
(7) Film removal timing. After aluminum profiles have been film-applied and painted, the film needs to be removed. However, it should not be removed immediately after spraying; proper timing must be controlled. Generally speaking, after spraying, a leveling process occurs until the paint film is basically solidified, which should take no less than 10 minutes before the film can be removed. Otherwise, if the paint film hasn't set, peeling off the film may leave residues on the aluminum profile and affect paint quality. Additionally, the removal motion should be swift to ensure the quality of the peel.
(8) Avoid multiple reworks. In the production of two-color aluminum profiles, rework is sometimes inevitable due to various factors. However, each rework requires another curing process. For the paint film, multiple coats increase the film thickness, and repeated curing weakens the adhesion, making the paint prone to peeling. Therefore, in the production of two-color aluminum profiles, multiple reworks should be avoided whenever possible.
(9) Reasonable control of film thickness: In the production of two-color aluminum profiles, spraying must be done more than once. If we operate as if it were a single spray, it will result in some areas of the topcoat being too thick and others too thin, causing severe unevenness in film thickness. Therefore, reasonable control is required during spraying. During the first spraying, focus on the key areas on one side, while the other side can be left unsprayed or lightly sprayed. The second spraying should focus on the areas that need coverage, while other areas are left unsprayed or lightly sprayed. At the same time, based on the first spraying and the chosen paint color, the thickness of the second spray should be reasonably controlled, ensuring that the second spraying properly covers the first one.
(10) Spraying sequence: In two-color aluminum profile processing, two paints are applied. There are always a dark color and a light color, so spraying must be done in sequence. Before spraying, it is necessary to consider which color should be applied first and which later, depending on the specific situation. If the light color is sprayed first and the dark color later, the light color will undergo two curing processes, which can cause discoloration. If the dark color is sprayed first and the light color later, the coverage of the spray for the dark color will be affected. To cover the dark color, the paint film thickness must be increased, but if the film becomes too thick, it is prone to peeling.




